Pelletizing Technology
Liquid Layering of Pellets by Fluid Bed Processing
For maximum production flexibility, GEA can supply a single fluid bed unit, the PRECISION-COATER, or a multi-purpose FlexStream processor that combines granulation, drying and pellet coating in a single piece of equipment.
Liquid Layering of Pellets
GEA's multi-functional PRECISION-COATER and FlexStream systems can both be used to make pellets by layering the active material onto an inert core. Non-pareil starter pellets are sprayed with a solution or suspension of the active material and dried simultaneously.
Coating Quality
Coating products can be expensive and the volume of product needed is inversely proportional to the particle size of the material to be coated. Coating quality is, therefore, of paramount importance.
The aim is to coat the particle with just enough coating material to achieve the desired result, but no more. In addition, when the coating is functional, it must also be evenly distributed over the entire surface of the product. An uneven application can seriously affect the performance (release profile) of the active. One cause of uneven coating can be the failure to generate sufficient rotation (spin) of the product during the process. Possibly resolved by increasing the airflow, this might, in turn, increase attrition losses owing to the generation of small, dust particles and reduce the yield.
Product Yield
In a traditional fluid bed coater, product can be lost as dust or by the agglomeration of larger, damp particles as they impact upon themselves or the equipment. Agglomeration is caused when the spray rate is too high and the product is still damp when it meets either another particle in the bed or the surface of the coater.
In some systems, the spray nozzle can cause a ‘venturi’ effect, sucking particles into an area of high humidity around the nozzle where they can collide and agglomerate. An increased airflow rate may offer a solution, or lowering the humidity in the vicinity of the spray nozzle by reducing the spray rate; however, this might result in increased losses through attrition or longer processing times.
Precision-Coater
For smaller particles such as powders, granules, seeds, crystals, pellets and small tablets, the PRECISION-COATER offers a time- and cost-effective alternative to traditional bottom spray coating systems.Features and Applications
The product is coated and partially dried by being blown upward through a central column with atomized liquid and drying air. The material falls into the outer part of the container where heated air completes the drying process.
On reaching the air distributor at the base of the module, the product flows into the central column for further coating. This process continues until the specified degree of coating is obtained.
Special features include high spray rates for short processes, highly controlled product movement and minimal agglomeration or granulation.
The PRECISION-COATER provides higher yields by reducing agglomeration and attrition; it improves productivity by accelerating the coating and drying process; and it significantly improves product quality by ensuring that a coating of uniform thickness is applied, thus ensuring optimal clinical efficacy. It is ideal for coating applications involving particles from 50 microns to 3 mm in diameter.
GEA believes that no other currently available product is better suited to the industry’s need for a highly effective coating system (pellet production) with excellent scale-up characteristics.
FlexStream
The GEA FlexStream fluid bed processor is a multi-purpose unit that uses proven fluid bed technology to achieve granulation, drying and pellet coating (or tablet coating) in a single piece of equipment.Process Description
The FlexStream comprises a fluid bed product bowl with several two-fluid atomization nozzles to distribute the granulation or coating liquid directly onto the fluidized powder or pellet layer.
A third low-pressure air stream comes directly from the fluid bed inlet plenum to create a particle-free area around the spray pattern of each nozzle. The low pressure results in much better control of the granulation and coating processes, fewer fines, less agglomeration when coating pellets and, as a result, significantly improved yields.
The FlexStream process is suitable for aqueous- and organic-based solvents. GEA offers a range of open- and closed-cycle systems to remove or recover organic solvents. Options include condensation, adsorption and wet scrubbing.
Process and Design
- A number of nozzles and achieved spray rates for pellet coating comparable with high efficiency bottom-spray coating systems
- Narrow particle size distribution for granulation Simple, cost-efficient design
- Compressed air only for atomization gas
- Third air stream conditioned from fluid bed air inlet
- 10 bar pressure shock resistant fluid bed processor design
- Existing GEA fluid bed equipment can be upgraded with the FlexStream process.
Downloads
Aanverwante producten
NICA Extruder System
The NICA Extruder is a low shear extruder that has been designed to offer low temperature handling of even the most sensitive products.
Wervelbedprocessing van farmaceutica
GEA levert wervelbedprocessors (in de VS beter bekend als wervelbed Multi-Processor™) voor mengen, granuleren, drogen, pelletiseren en coaten in de farmaceutische industrie.
NICA Integrated Pelletizing Systems
Developed specifically for the Pharmaceutical industry, the NICA Integrated Pelletizing Systems (IPS) fuses NICA Extrusion and Spheronization technologies to create a range of compact, continuous systems for the production of spherical pellets.
NICA Spheronizer System
Developed specifically for the pharmaceutical industry, NICA Spheronizers deliver spherical pellets at fast production rates using patented technology to maximize yields.
GEA-inzichten
Het volgende tijdperk van voedselproductie met GEA NEXUS
Klimaatverandering en een groeiende wereldbevolking zetten de energie-intensieve voedselindustrie onder toenemende druk om meer mensen te voeden zonder de planeet verder te belasten. George Shepherd, GEA's Global Technical Sustainability Manager, legt uit hoe GEA zijn technische knowhow gebruikt om verwerkers te helpen duurzamer te produceren en tegelijkertijd de productiviteit te verhogen.
Making milk production more sustainable for a growing world
The world's population is growing and with it demand for milk. Dairy is an essential component of many global diets. However, its production can be resource-intensive and impact the environment. GEA’s Christian Müller, Senior Director Sustainability Farm Technologies, sheds light on how technological innovations powered by GEA make milk production more efficient and profitable.
Schone machines voor veilige voedingsmiddelen: de kracht van hygiënisch ontwerp
Elk veilige drankje en hapje eten is een overwinning op onzichtbare microbiële dreigingen; een strijd die wordt gestreden door een eeuw van hygiënisch procesontwerp. Met meer dan 100 jaar ervaring in engineering en hygiënische ontwerpkennis stelt GEA de industrienorm voor verwerkingsapparatuur die voedingsmiddelen beschermt en levens redt.
